|Edition Number:||5||SCC Approved:||--|
|Edition Date:||2016-08-03||DOD Approved:||--|
|Price Code:||H||ANSI Approved:||2016-08-03|
In general, this part of IEC 60730 applies to automatic ELECTRICAL CONTROLS for use in, on, or in association with equipment for household and similar use. The equipment may use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof.
NOTE 1 Throughout this standard the word "equipment" means "appliance and equipment."
EXAMPLE 1 CONTROLS for appliances within the scope of IEC 60335.
This International Standard is applicable to CONTROLS for building automation within the scope of ISO 16484.
This standard also applies to automatic ELECTRICAL CONTROLS for equipment that may be used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications.
EXAMPLE 2 CONTROLS for commercial catering, heating and air-conditioning equipment.
This standard is also applicable to individual CONTROLS utilized as part of a CONTROL system or CONTROLS which are mechanically integral with multifunctional CONTROLS having non-electrical outputs.
EXAMPLE 3 Independently mounted water valves, CONTROLS in smart grid systems and CONTROLS for building automation systems within the scope of ISO 16484-2.
This standard is also applicable to relays when used as CONTROLS for IEC 60335 appliances. Additional requirements for the safety and OPERATING VALUES of relays when used as CONTROLS for IEC 60335 appliances are contained in Annex u.
NOTE 2 These requirements are referred to in the scope of IEC 61810-1.
NOTE 3 This standard is intended to be used for the testing of any stand-alone relay which is intended to be used as a CONTROL of an appliance according to IEC 60335-1. It is not intended to be used for any other stand-alone relay, or to replace the IEC 61810 series of standards.
This standard does not apply to automatic ELECTRICAL CONTROLS intended exclusively for industrial process applications unless explicitly mentioned in the relevant part 2 or the equipment standard.
This standard applies to CONTROLS powered by primary or secondary batteries, requirements for which are contained within the standard, including Annex v.
1.1.1 This International Standard applies to the inherent safety, to the OPERATING VALUES, OPERATING TIMES, and OPERATING SEQUENCES where such are associated with equipment safety, and to the testing of automatic ELECTRICAL CONTROL devices used in, or in association with, equipment.
This standard applies to CONTROLS using THERMISTORS, see also Annex j.
This standard is also applicable to the FUNCTIONAL SAFETY of LOW COMPLEXITY SAFETY RELATED SYSTEMS and CONTROLS.
1.1.2 This standard applies to automatic ELECTRICAL CONTROLS, mechanically or electrically operated, responsive to or controlling such characteristics as temperature, pressure, passage of time, humidity, light, electrostatic effects, flow, or liquid level, current, voltage, acceleration, or combinations thereof.
1.1.3 This standard applies to starting relays, which are a specific type of automatic ELECTRICAL CONTROL, intended to switch the starting winding of a motor. Such CONTROLS may be built into, or be separate from, the motor.
1.1.4 This standard applies to MANUAL CONTROLS when such are electrically and/or mechanically integral with AUTOMATIC CONTROLS.
NOTE Requirements for manual switches not forming part of an AUTOMATIC CONTROL are contained in IEC 61058-1.
1.1.5 This standard applies to a.c. or d.c. powered CONTROLS with a rated voltage not exceeding 690 V a.c. or 600 V d.c.
1.1.6 This standard does not take into account the RESPONSE VALUE of an AUTOMATIC ACTION of a CONTROL, if such a RESPONSE VALUE is dependent upon the method of mounting the CONTROL in the equipment. Where a RESPONSE VALUE is of significant purpose for the protection of the USER, or surroundings, the value defined in the appropriate household equipment standard or as determined by the manufacturer shall apply.
1.1.7 This standard applies also to CONTROLS incorporating ELECTRONIC DEVICES, requirements for which are contained in Annex h.
1.1.7DV.1 Modification of 1.1.7 by adding the following text:
This standard applies to discrete THERMISTORS and also to controls using NTC or PTC THERMISTORS, requirements for which are contained in Annex j
1.1.8 This standard applies also to CONTROLS using NTC or PTC THERMISTORS, requirements for which are contained in Annex j.
1.1.9 This standard applies to the electrical and FUNCTIONAL SAFETY of CONTROLS capable of receiving and responding to communications signals, including signals for power billing rate and demand response.
The signals may be transmitted to or received from external units being part of the CONTROL (wired), or to and from external units which are not part of the CONTROL (wireless) under test.
1.1.10 This standard does not address the integrity of the output signal to the network devices, such as interoperability with other devices unless it has been evaluated as part of the CONTROL SYSTEM.
1.1.101DV Addition to the Scope by adding the following text:
CONTROLS intended to be installed in air handling spaces or in other environmental air space (plenums) are covered under the scope of this standard.
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
IEC 60038, IEC standard voltages
IEC 60065:2001, Audio, video and similar electronic apparatus – Safety requirements1; Amendment 1:2005; Amendment 2:2010
1 There exists a consolidated edition 7.2:2011 including IEC 60065:2001 and its Amendments 1:2005 and 2:2010.
IEC 60068-2-75, Environmental testing – Part 2-75: Tests – Test Eh: Hammer tests
IEC 60085, Electrical insulation – Thermal evaluation and designation
IEC 60099-1, Surge arresters – Part 1: Non-linear resistor type gapped arresters for a.c. systems2
IEC 60112:2003, Method for the determination of the proof and the comparative tracking indices of solid insulating materials3; Amendment 1:2009
3 There exists a consolidated edition 4.1:2009 including IEC 60112:2003 and its Amendment 1:2009.
IEC 60127-1, Miniature fuses – Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links
IEC 60227-1, Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V – Part 1: General requirements
IEC 60245-1, Rubber insulated cables – Rated voltages up to and including 450/750 V – Part 1: General requirements
IEC 60269-1, Low-voltage fuses – Part 1: General requirements
IEC 60335-1:2010, Household and similar electrical appliances – Safety – Part 1: General requirements
IEC 60364 (all parts), Low-voltage electrical installations
IEC 60384-14, Fixed capacitors for use in electronic equipment – Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains
IEC 60384-16, Fixed capacitors for use in electronic equipment – Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors
IEC 60384-17, Fixed capacitors for use in electronic equipment – Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors
IEC 60417 (all parts), Graphical symbols for use on equipment
IEC 60423, Conduit systems for cable management – Outside diameters of conduits for electrical installations and threads for conduits and fittings
IEC 60529:1989, Degrees of protection provided by enclosures (IP code)4; Amendment 1:1999
4 There exists a consolidated edition 2.1:2001 including IEC 60529:1989 and its Amendment 1:1999.
IEC 60539 (all parts), Directly heated negative temperature coefficient thermistors
IEC 60664-1:2007, Insulation coordination for equipment within low-voltage systems – Part 1: Principles, requirements and tests
IEC 60664-3:2003, Insulation coordination for equipment within low-voltage systems – Part 3: Use of coating, potting or moulding for protection against pollution; Amendment 1:2010
IEC 60664-4, Insulation coordination for equipment within low-voltage systems – Part 4: Consideration of high-frequency voltage stress
IEC 60695-2-10, Fire Hazard testing – Part 2-10: Glowing/hot-wire based test methods – Glow-wire apparatus and common test procedure
IEC 60695-2-11:2000, Fire hazard testing – Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products
IEC 60695-10-2, Fire hazard testing – Part 10-2: Abnormal heat – Ball pressure test
IEC 60738-1, Thermistors – Directly heated positive temperature coefficient – Part 1: Generic specification
IEC 60738-1-1, Thermistors – Directly heated positive step-function temperature coefficient – Part 1-1: Blank detail specification – Current limiting application – Assessment level EZ
IEC 60947-1:2007, Low-voltage switchgear and controlgear – Part 1: General rules
IEC 60998-2-2, Connecting devices for low-voltage circuits for household and similar purposes – Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
IEC 60998-2-3, Connecting devices for low-voltage circuits for household and similar purposes – Part 2-3: Particular requirements for connecting devices as separate entities with insulation-piercing clamping units
IEC 60999-1, Connecting devices – Electrical copper conductors – Safety requirements for screw-type and screwless-type clamping units – Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
IEC 61000 (all parts), Electromagnetic compatibility (EMC)
IEC 61000-3-2, Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equipment input current ≤ 16 A per phase)
IEC 61000-3-3:2008, Electromagnetic compatibility (EMC) – Part 3-3: Limits – Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤16 A per phase and not subject to conditional connection
IEC 61000-4-2:2008, Electromagnetic compatibility (EMC) – Part 4-2: Testing and measurement techniques – Electrostatic discharge immunity test
IEC 61000-4-3, Electromagnetic compatibility (EMC) – Part 4-3: Testing and measurement techniques – Radiated, radio-frequency, electromagnetic field immunity test
IEC 61000-4-4, Electromagnetic compatibility (EMC) – Part 4-4: Testing and measurement techniques – Electrical fast transient/burst immunity test
IEC 61000-4-5, Electromagnetic compatibility (EMC) – Part 4-5: Testing and measurement techniques – Surge immunity test
IEC 61000-4-6, Electromagnetic compatibility (EMC) – Part 4-6: Testing and measurement techniques – Immunity to conducted disturbances, induced by radio-frequency fields
IEC 61000-4-8, Electromagnetic compatibility (EMC) – Part 4-8: Testing and measurement techniques – Power frequency magnetic field immunity test
IEC 61000-4-11, Electromagnetic compatibility (EMC) – Part 4-11: Testing and measurement techniques – Voltage dips, short interruptions and voltage variations immunity tests
IEC 61000-4-13:2002, Electromagnetic compatibility (EMC) – Part 4-13: Testing and measurement techniques – Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity tests; Amendment 1:2009
IEC 61000-4-28, Electromagnetic compatibility (EMC) – Part 4-28: Testing and measurements techniques – Variation of power frequency, immunity test
IEC 61058-1, Switches for appliances – Part 1: General requirements
IEC 61210, Connecting devices – Flat quick-connect terminations for electrical copper conductors – Safety requirements
IEC 61249 (all parts), Materials for printed boards and other interconnecting structures
IEC 61558-2-6, Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V – Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
IEC 61558-2-16, Safety of transformers, reactors, power supply units and similar products for voltages up to 1 100 V – Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
IEC 61643-11, Low-voltage surge protective devices – Part 11: Surge protective devices connected to low-voltage power systems – Requirements and test methods
IEC 62151, Safety of equipment electrically connected to a telecommunication network
IEC 62326 (all parts), Printed boards
IEC 62368-1, Audio/video, information and communication technology equipment – Part 1: Safety requirements
CISPR 11, Industrial, scientific and medical equipment – Radio-frequency disturbance characteristics – Limits and methods of measurement
CISPR 14-1:2005, Electromagnetic compatibility – Requirements for household appliances, electric tools and similar apparatus – Part 1: Emission5; Amendment 1:2008
5 There exists a consolidated edition 5.1:2009 including CISPR 14-1:2005 and its Amendment 1:2008.
CISPR 22:2008, Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement
ISO 16484-2, Building automation and control systems (BACS) – Part 2: Hardware
1.2DV Addition of the following to 1.2:
The following UL Standards are referenced in this Standard:
UL 50 Enclosures for Electrical Equipment, Non-Environmental Considerations
UL 50E Enclosures for Electrical Equipment, Environmental Considerations
UL 62 Flexible Cords and Cables
UL 94 Plastic Materials for Parts in Devices and Appliances, Tests for Flammability of
UL 157 Gaskets and Seals
UL 248-14 Low-Voltage Fuses – Part 14: Supplemental Fuses
UL 310 Terminals, Electrically Quick-Connect
UL 508 Industrial Control Equipment
UL 514A Metallic Outlet Boxes
UL 514B Fittings, Conduit, Tubing and Cable
UL 514C Nonmetallic Outlet Boxes, Flush-Device Boxes, and Covers
UL 635 Insulating Bushings
UL 746C Polymeric Materials – Use in Electrical Equipment Evaluations
UL 796 Printed-Wiring Boards
UL 969 Marking and Labeling Systems
UL 1059 Terminal Blocks
UL 4200A Products Incorporating Button or Coin Cell Batteries of Lithium Technologies
UL 4248 Fuseholders series
UL 5085-1 Low Voltage Transformers – Part 1: General Requirements
UL 5085-2 Low Voltage Transformers – Part 2: General Purpose Transformers
UL 5085-3 Low Voltage Transformers – Part 3: Class 2 and Class 3 Transformers