UL 60691
Standard for Thermal-Links - Requirements and Application Guide

DETAILS
Edition Number:4SCC Approved:--
Edition Date:2016-06-30DOD Approved: --
Price Code:EANSI Approved: 2016-06-30
Type:uleciaiec

  • SCOPE

    1 Scope

    This International Standard is applicable to THERMAL-LINKS intended for incorporation in electrical appliances, electronic equipment and component parts thereof, normally intended for use indoors, in order to protect them against excessive temperatures under abnormal conditions.

    The equipment is not designed to generate heat.

    The effectiveness of the protection against excessive temperatures logically depends upon the position and method of mounting of the THERMAL-LINK, as well as upon the current which it is carrying.

    This standard may be applicable to THERMAL-LINKS for use under conditions other than indoors, provided that the climatic and other circumstances in the immediate surroundings of such THERMAL-LINKS are comparable with those in this standard.

    This standard may be applicable to THERMAL-LINKS in their simplest forms (e.g. melting strips or wires), provided that molten materials expelled during function cannot adversely interfere with the safe use of the equipment, especially in the case of hand-held or PORTABLE EQUIPMENT, irrespective of its position.

    Annex h of this standard is applicable to THERMAL-LINK packaged assemblies where the thermal-link(s) has already been approved to this standard but packaged in a metallic or non-metallic housing and provided with terminals/wiring leads.

    This standard is applicable to THERMAL-LINKS with a RATED VOLTAGE not exceeding 690 V a.c. or d.c. and a RATED CURRENT not exceeding 63 A.

    The objectives of this standard are:

    a)    to establish uniform requirements for THERMAL-LINKS,

    b)    to define methods of test,

    c)    to provide useful information for the application of THERMAL-LINKS in equipment.

    This standard is not applicable to THERMAL-LINKS used under extreme conditions such as corrosive or explosive atmospheres.

    This standard is not applicable to THERMAL-LINKS to be used in circuits on a.c. with a frequency lower than 45 Hz or higher than 62 Hz.

    1DV Modification of the fifth paragraph to add the following:

    The maximum current is unlimited.

  • TABLE OF CONTENTS
    Expand All

    • Cover
    • Transmittal
    • UL Harmonized Standard Title Page
    • Table of Contents
    • Deviations
    • IEC Foreword
    • IEC Preface
    • Introduction
      • THERMAL-LINKS – REQUIREMENTS AND APPLICATION GUIDE
        • 1 Scope
        • 2 Normative references
        • 3 Terms and definitions
        • 4 General requirements
        • 5 General notes on tests
        • 6 Classification
          • 6.1 Electrical conditions
          • 6.2 Thermal conditions
          • 6.3 Resistance to tracking
        • 7 Marking
        • 8 Documentation
        • 9 Constructional requirements
          • 9.1 General
          • 9.2 Lead secureness tests
          • 9.3 Contacts used for the current path
          • 9.4 Accessible mounting brackets or metal parts
          • 9.5 Insulating materials
          • 9.6 Resistance to tracking
          • 9.7 CREEPAGE DISTANCES and CLEARANCES
          • 9.8 Temperature and humidity cycle conditioning
          • 9.9 Terminals and terminations
        • 10 Electrical requirements
          • 10.1 Dielectric strength
          • 10.2 Insulation resistance
          • 10.3 INTERRUPTING CURRENT
          • 10.5 Limited short-circuit test
        • 11 Temperature tests
          • 11.1 General
          • 11.2 HOLDING TEMPERATURE, T
          • 11.3 RATED FUNCTIONING TEMPERATURE, T
          • 11.4 MAXIMUM TEMPERATURE LIMIT, T
          • 11.5 Ageing
        • 12 Resistance to rusting
        • 13 Manufacturer's validation programme
    • Annex A(normative)Application guide
    • Annex B(normative)Alternative ageing test for THERMAL-LINKS with Tgreater than 250°C for use in electric irons
    • Annex C(normative)Conductive heat ageing test
    • Annex D(informative)EXTENDED HOLDING TEMPERATURE evaluation
    • Annex E(normative)Seal ageing test
    • Annex F(normative)Identification requirements
    • Annex G(normative)Indelibility of markings
    • Annex H(normative)Requirements for THERMAL-LINK packaged assemblies
    • Bibliography