UL 2586
Standard for Hose Nozzle Valves

DETAILS
Edition Number:1SCC Approved:--
Edition Date:2011-04-29DOD Approved: --
Price Code:AANSI Approved: 2018-10-01
Type:ulstd

  • SCOPE

    1 Scope

    1.1 These requirements cover hose nozzle valves that are intended to be used for the control of flammable and combustible liquids. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with flammable fluids which are handled at temperatures within the range of minus 29°C (minus 20°F) to 52°C (125°F) and an operating pressure of minimum 50 psi (350 kPa).

    1.2 These requirements cover hose nozzle valves of the manually operated and automatic pressure operated type.

    When they form a part of an assembly which provides for additional functions or service, the requirements are outside the scope of these requirements.

    1.3 These requirements do not cover the following:

    a)    Hose nozzle valves for handling liquids under cryogenic conditions.

    b)    Hose nozzle valves for general refinery service, offshore and pipe line terminals, natural gas processing plants, gas distribution systems, petrochemical processing facilities, or the like.

    c)    Hose nozzle valves operated wholly or partially by electricity or battery.

    1.4 For hose nozzle valves intended to be used with gasoline/ethanol blends with nominal ethanol concentrations above 10%, refer to the Standard for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 – E85), UL 2586A, for additional requirements.

    1.5 For additional requirements for hose nozzle valves for diesel fuel, biodiesel fuel, diesel/biodiesel blends with nominal biodiesel concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil refer to the Standard for Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 2586B.

    1.6 Requirements for the installation and use of these dispensing devices are included in the Code for Motor Fuel Dispensing Facilities and Repair Garages, NFPA 30A.

  • TABLE OF CONTENTS
    Expand All

    • Cover
    • Transmittal
    • Table of Contents
      • Body
        • INTRODUCTION
          • 1 Scope
          • 2 General
            • 2.1 Components
            • 2.2 Units of measurement
            • 2.3 Undated references
          • 3 Glossary
        • CONSTRUCTION
          • 4 Assembly
            • 4.1 General
            • 4.2 Hose nozzle valves
          • 5 Materials
          • 6 Bodies and Covers
          • 7 Diaphragms
          • 8 Springs
          • 9 Operating Mechanisms
        • PERFORMANCE
          • 10 General
          • 11 Deformation Test
          • 12 External Leakage Test
          • 13 Seat Leakage Test
          • 14 Hose Nozzle Valve Guard Strength Test
          • 15 Operation Test
            • 15.1 Automatic hose nozzle valve
            • 15.2 Bellows Secondary Shut Off Operation
          • 16 Pull Test
          • 17 Sensitivity Test
          • 18 Hose Nozzle Endurance Test
          • 19 Bellows Secondary Shut Off Operation Test
          • 20 Visible Discharge Indicator Tests
            • 20.1 Thermal shock test
            • 20.2 Drop test
          • 21 Hydrostatic Strength Test
          • 22 Electrical Continuity Test
          • 23 Salt Spray Test
          • 24 Moist Ammonia-Air Stress Cracking Test
          • 25 Tests of Synthetic Rubber Parts
            • 25.1 General
            • 25.2 Volume change test
            • 25.3 Weight loss test
            • 25.4 Accelerated aging test
          • 26 Marking Adhesion Test
        • MANUFACTURING AND PRODUCTION TESTS
          • 27 General
        • INSTALLATION INSTRUCTIONS
          • 28 General
        • MARKING
          • 29 General