UL 19
Standard for Lined Fire Hose and Hose Assemblies

DETAILS
Edition Number:13SCC Approved:--
Edition Date:2013-10-25DOD Approved: 1999-04-05
Price Code:DANSI Approved: 2013-10-24
Type:ulstd

  • SCOPE

    1 Scope

    1.1 These requirements cover single- and multiple-jacketed lined fire hose with or without couplings attached, in the trade sizes of 1-1/2, 1-3/4, 2, 2-1/2, 3, 3-1/2, 4, 5, and 6 inch (38, 45, 51, 65, 76, 89, 102, 127, and 152 mm nominal ID). Single-jacketed hose is intended for service test pressures of 150, 200, or 250 psig (1035, 1380, or 1725 kPa). Multiple-jacketed hose or covered hose judged equivalent to multiple-jacketed hose is intended for service test pressures of 200, 300, or 400 psig (1380, 2070, or 2760 kPa).

    1.2 These products are intended for municipal and industrial fire protection purposes. Single-jacketed hose is for use at fire hydrants, standpipes, and similar places. They are not intended for hard usage nor where the hose will be subjected to chafing on rough or sharp surfaces. Multiple-jacketed hose or covered hose judged equivalent to multiple-jacketed hose are for use on pumpers and in places where service conditions require the additional protection against wear afforded by the extra woven jacket or cover.

    1.3 The products covered by these requirements are intended to be periodically inspected and maintained while in service, as outlined in the Standard for the Care, Use, Inspection, Service Testing and Replacement of Fire Hose, Couplings, Nozzles, and Fire Hose Appliances, NFPA 1962.

  • TABLE OF CONTENTS
    Expand All

    • Cover
    • Transmittal
    • Table of Contents
      • Body
        • INTRODUCTION
          • 1 Scope
          • 2 General
            • 2.1 Units of measurement
            • 2.2 Undated references
          • 3 Glossary
        • CONSTRUCTION
          • 4 Internal Diameter
          • 5 Jacket and Inner Reinforcements
          • 6 Lining
          • 7 Cover
          • 8 Coatings and Treatments
          • 9 Couplings
        • PERFORMANCE
          • 10 Hydrostatic Proof-Pressure Tests
            • 10.1 General
            • 10.2 Sample
            • 10.3 Equipment
            • 10.4 Test method
          • 11 Kink Test
            • 11.1 General
            • 11.2 Sample
            • 11.3 Equipment
            • 11.4 Test method
          • 12 Hydrostatic Strength Test
            • 12.1 General
            • 12.2 Sample
            • 12.3 Equipment
            • 12.4 Test method
          • 13 Repeated Bending Test
            • 13.1 General
            • 13.2 Sample
            • 13.3 Equipment
            • 13.4 Test method
          • 14 Alternating Pressure Test
            • 14.1 General
            • 14.2 Sample
            • 14.3 Equipment
            • 14.4 Test method
          • 15 Abrasion Test
            • 15.1 General
            • 15.2 Sample
            • 15.3 Equipment
            • 15.4 Test method
          • 16 Heat-Resistance Test
            • 16.1 General
            • 16.2 Sample
            • 16.3 Equipment
            • 16.4 Test method
          • 17 Fold-Resistance Test
            • 17.1 General
            • 17.2 Sample
            • 17.3 Equipment
            • 17.4 Test method
          • 18 Wet Hose Test
            • 18.1 General
            • 18.2 Sample
            • 18.3 Test method
          • 19 Low-Temperature Test
            • 19.1 General
            • 19.2 Sample
            • 19.3 Equipment
            • 19.4 Test method
          • 20 Coupling Retention Test
            • 20.1 General
            • 20.2 Sample
            • 20.3 Equipment
            • 20.4 Test method
          • 21 Friction Loss Test
            • 21.1 General
            • 21.2 Sample
            • 21.3 Equipment
            • 21.4 Test method
          • 22 Accelerated Aging Test of Threads
            • 22.1 General
            • 22.2 Sample
            • 22.3 Equipment
            • 22.4 Test method
          • 23 Adhesion Tests
            • 23.1 General
            • 23.2 Sample
            • 23.3 Equipment
            • 23.4 Test method
          • 24 Accelerated Aging Test of Linings and Covers
            • 24.1 General
            • 24.2 Sample
            • 24.3 Equipment
            • 24.4 Test method
          • 25 Ozone-Exposure Test of Linings and Covers
            • 25.1 General
            • 25.2 Sample
            • 25.3 Equipment
            • 25.4 Test method
          • 26 Water Immersion Test of Linings
            • 26.1 General
            • 26.2 Sample
            • 26.3 Equipment
            • 26.4 Method – Effect on tensile strength and ultimate elongation
            • 26.5 Method – Effect on volume
          • 27 Pull Test
            • 27.1 General
            • 27.2 Sample
            • 27.3 Test method
          • 28 Accelerated Aging Test of Hose Assembly
            • 28.1 General
            • 28.2 Sample
            • 28.3 Equipment
            • 28.4 Test method
          • 29 Rough Usage Test
            • 29.1 General
            • 29.2 Sample
            • 29.3 Equipment
            • 29.4 Test method
          • 30 Moist Ammonia-Air Stress Cracking Test
            • 30.1 General
            • 30.2 Sample
            • 30.3 Equipment
            • 30.4 Method
          • 31 Salt-Spray Corrosion Test
            • 31.1 General
            • 31.2 Sample
            • 31.3 Equipment
            • 31.4 Test method
          • 32 Accelerated Aging Test of Gaskets
            • 32.1 General
            • 32.2 Sample
            • 32.3 Equipment
            • 32.4 Test method
          • 33 Compression Set Test
            • 33.1 General
            • 33.2 Samples
            • 33.3 Equipment
            • 33.4 Test method
          • 34 Ozone Resistance Test of Gaskets
            • 34.1 General
            • 34.2 Sample
            • 34.3 Equipment
            • 34.4 Test method
          • 35 Water Immersion Test of Gaskets
            • 35.1 General
            • 35.2 Sample
        • MANUFACTURING AND PRODUCTION TESTS
          • 36 General
        • MARKING
          • 37 Details
            • 37.1 General
            • 37.2 Hose
            • 37.3 Hose Assemblies