UL 1008M
Transfer Switch Equipment, Meter Mounted

DETAILS
Edition Number:2SCC Approved:--
Edition Date:2015-08-28DOD Approved: --
Price Code:AANSI Approved: --
Type:outline

  • SCOPE

    1 Scope

    1.1 These requirements cover automatic and non-automatic (manual) transfer switch equipment, operating at 600 V ac less, and intended for installation in a utility meter base, in ordinary locations only.

    1.2 These devices are intended for use in optional standby systems only, and are not intended for use in Emergency or Legally Required Standby Systems. These devices are intended for one of the following applications:

    a)    Cord connection of a portable generator to power a premise wiring system, where the neutral (grounded circuit conductor) of the generator is not bonded to ground or the generator frame, and bonding of the neutral (grounded circuit conductor) to ground will occur within the meter base or

    b)    Permanent connection of a stationary generator to power a premise wiring system, where the generator is connected as a non-seperately derived system, where the neutral (grounded circuit conductor) of the generator is not bonded to ground or the generator frame.

    1.3 These devices are connected between the meter mounting equipment and the electric utility meter, on the line side of the service disconnect. As such, the installation of these devices is intended to be under the exclusive control of the serving utility, and these are not considered under the purview of the National Electrical Code, NFPA 70. Generators and associated wiring connected to the generator terminals of the transfer switch are not considered under the exclusive control of the utility, and are under the purview of NFPA 70.

    1.4 An automatic transfer switch as covered by these requirements is a device that automatically transfers a common load from a normal supply to an alternate supply in the event of failure of the normal supply, and automatically returns the load to the normal supply when the normal supply is restored. An automatic transfer switch may be provided with a logic control circuit that inhibits automatic operation of the device from either a normal to an alternate supply, or from an alternate to a normal supply when the switch reverts to automatic operation upon loss of power to the load.

    1.5 A non-automatic transfer switch as covered by these requirements is a device, operated manually by a physical action, or electrically by a remote control, for transferring a common load between a normal and alternate supply.

    1.6 A transfer switch may incorporate overcurrent protection for the main power circuits.

    1.7 These requirements only cover transfer switches which are completely enclosed when installed in a meter base in conjunction with the electrical utility meter.

    1.8 Transfer switches are rated in amperes and are considered to be acceptable for total system transfer, which includes control of motors, electric-heating loads, and transformer loads.

  • TABLE OF CONTENTS
    Expand All

    • Outline Title Page
    • Table of Contents
      • Body
        • INTRODUCTION
          • 1 Scope
          • 2 Components
          • 3 Units of Measurement
          • 4 Undated References
        • CONSTRUCTION
          • 5 General
          • 6 Enclosure
          • 7 Insulating Material
          • 8 Mounting of Parts
          • 9 Guarding and Accessibility of Live Parts
          • 10 Current-Carrying Parts
          • 11 Field Wiring Terminals
          • 12 Internal Wiring
          • 13 Grounding and Bonding
          • 14 Operating Mechanism
            • 14.1 General
            • 14.2 Location and protection of transfer control circuits
          • 15 Receptacles
          • 16 Inlets for Cord Connection to a Portable Generator
          • 17 Spacings
            • 17.1 General
            • 17.2 Spacings on printed wiring boards
        • PERFORMANCE
          • 18 General
          • 19 Normal Operation Test
          • 20 Overvoltage Test
          • 21 Undervoltage Test
          • 22 Overload Test
          • 23 Temperature Test
          • 24 Endurance Test
          • 25 Dielectric Voltage-Withstand Test
          • 26 Withstand
          • 27 Closing
        • RATINGS
          • 28 Details
        • MARKINGS
          • 29 Content
          • 30 Permanence of Marking